Selection & Purchasing

Five Ways a Fine-Grit Order Goes Wrong (F150-F320)

Fine grits are where small ordering errors cost the most. A coarse grit bought slightly wrong still does the job; a fine grit bought slightly wrong clogs a nozzle, changes a…

TECHNICAL GUIDE / 2026-11-16

Five Ways a Fine-Grit Order Goes Wrong (F150-F320)

Fine grits are where small ordering errors cost the most. A coarse grit bought slightly wrong still does the job; a fine grit bought slightly wrong clogs a nozzle, changes a finish, or fails a batch test. The five mistakes below come up again and again with F150 to F320 orders. Each one is cheap to prevent before the order is placed, and expensive to fix after the material arrives.

1. Judging a fine grit by a coarse grit's chemistry

The most common fine-grit complaint is also the least justified: a buyer reads about 93% alumina on the batch report and concludes the material is substandard, because the coarse grades they buy run higher. For example, the A grade of F46 brown fused alumina runs 95.00–97.50% Al2O3. A fine grit in the F150–F320 range running around 93% is not a weaker version of the same product — it is a different size fraction with its own specification, and around 93% is the normal range for these sizes.

The error is comparing a fine grit against a limit written for a coarse grit. Every size has its own chemical limits, and the batch report for a fine grit should be judged against the limits for that size, not against the numbers on a different product's data sheet. Our buyers' FAQ explains why fine grits run about 93% alumina — and why that is normal.

The check before you order: ask for the chemical limits for the exact size you are buying, and confirm that the batch report will be judged against those limits. If the limits are agreed in writing before the order, a 93% result is a pass, not a dispute.

2. Mixing up 200F/320F powder with F150–F320 grit

The numbers look alike, and that is exactly the trap. 200F and 320F are mesh-to-zero fine powders — material ground so that everything passes a 200 or 320 mesh screen — used in refractory and casting formulations. F150 to F320 are FEPA F-grit macrogrits, sized by a different system for abrasive use. Same digits, different products, different test methods, different behaviour in the process.

Ordering "320F" when the process needs F320 grit, or the other way round, delivers a material that cannot do the job — and the mistake is only discovered when the material is already on the production line. Our guide to 200F vs 320F refractory fine powder covers the powder side in detail; the point here is not to let the two designations share one order line.

The check before you order: write the designation system on the order, not just the number — "FEPA F320" or "320 mesh to zero" — and state the intended use in the same line. Our fine powder range runs 150, 180, 220 and 320 mesh to zero, so the distinction has to be explicit for the order to be filled correctly.

3. Treating a mesh or micron conversion as an exact size

A buyer finds a conversion table, turns a mesh number into microns, turns the microns into a FEPA F number, and orders by the converted value. The problem is that mesh, microns and FEPA F numbers are three different ways of describing size, and every conversion table is an approximation. Two tables can give two different answers for the same grit, and a grit ordered by a converted value may not match the sieve limits the process actually needs.

The safe unit is the one the supplier tests against: the FEPA F number plus the sieve distribution limits, confirmed in the agreed specification and checked on the batch report. Anything converted from another system is a starting point for discussion, not an order specification.

The check before you order: put the FEPA F number and the sieve limits in the order, and ask for the distribution to be confirmed on the batch test report for the lot shipped. The F grit range is supplied to the agreed specification for the order, and the batch report is the record that the agreed distribution was met.

4. Ignoring moisture and caking

Fine powder has far more surface area per tonne than coarse grit, so it picks up moisture faster and clumps sooner. A delivery that was free-flowing at the factory can arrive as lumps if the packing or the storage is wrong, and lumpy fine powder feeds unevenly, blocks dosing equipment, and mixes poorly into a refractory or casting batch.

This is a storage and packing question, not a material defect — but it becomes the buyer's problem the moment the bags are opened. Dry packing, dry storage, and a check on arrival cost almost nothing; re-drying or re-screening a caked delivery costs a production day.

The check before you order: confirm the packing and the storage conditions with the order, and inspect the material on arrival before it goes into stock. Our guide to moisture control in export storage covers the practical steps — dry warehouse, sealed bags, first-in-first-out rotation — that keep fine powder free-flowing until use.

5. Sampling from the top of one bag

Fine grit segregates in transit: vibration sorts the particles, so the top of a bag is not the same as the bottom, and one bag is not the same as the next. A single scoop from the top of a single bag tells you about that scoop, not about the lot — yet that is the sample most disputes are built on.

A representative sample is drawn across bags and across the lot, following the sampling method agreed with the supplier, and it is compared with the batch test report issued for that lot — not with a data sheet, and not with a previous lot's numbers. Our guide to reading a batch test report before you buy explains which lines on the report matter and which values are reference ranges.

The check before you order: agree the sampling method and the acceptance limits in writing, and keep a retained sample from the same lot. If a result is ever questioned, the retained sample and the batch report settle it in minutes; without them, it becomes an argument.

The five checks, on one line each

  1. Confirm the chemical limits for your exact size — 93% is normal for F150–F320.
  2. Write the designation system on the order — FEPA F or mesh to zero.
  3. Order by FEPA F number plus sieve limits, never by a converted value.
  4. Confirm dry packing and storage, and inspect on arrival.
  5. Sample across the lot and judge the result against that lot's batch report.

Fine grits reward buyers who specify precisely and punish buyers who order by habit. Send the grade, the size, the quantity, the packing and the destination port, and Luoyang Naibao New Materials Co., Ltd. will confirm the specification and the batch report that will accompany the shipment — before the order is placed, not after it arrives.

Related technical guidance

Specific chemical, size and performance values are subject to the agreed product specification, technical agreement and batch test result.

INQUIRY

Request product information

Share the intended process, grade or size, required standard, quantity and any working sample. We will review the requirement and reply by email.

Optional. Please do not include sensitive information beyond what is needed for this inquiry.

Cookie preferences

Essential storage keeps your choice. Analytics helps us understand visits and is optional.